Loading...
Loading...
Loading...
Loading...
L.E. Wilson
The L.E. Wilson 6.5 Grendel bushing full length die is a precision reloading die built for shooters who want control over neck tension without sizing the entire neck. If you're loading for your 6.5 Grendel and looking to improve consistency and accuracy, this die gives you the flexibility to dial in your exact brass dimensions. It sizes the case body and shoulder while leaving the bottom 3/16" of the neck unsized—a technique many serious reloaders prefer for tighter round-to-round consistency and better chamber fit.
L.E. Wilson's bushing-type full length dies are engineered differently than conventional sizing dies. The die works with interchangeable neck bushings (sold separately) so you can match your specific brass and desired neck tension without resizing the entire neck. This modularity means you're not locked into one neck diameter; swap a bushing and adjust your load as your brass changes or your needs evolve. The die includes an adjustable depth decapping rod and a spare decapping punch, so you're ready to start sizing cases right away.
Built from heat-treated steel hardened to L.E. Wilson's specs—tougher than Grade 8 bolts—this die is made to handle thousands of rounds without wear or tolerance creep. It uses stainless lock nuts and other durable components to resist corrosion and maintain a long, accurate service life. The die fits standard 7/8"-14 reloading presses and integrates seamlessly into any established bench setup. Neck bushings are sold separately; L.E. Wilson bushings are recommended, though Redding bushings will also fit.
This is the right choice if you're a meticulous 6.5 Grendel handloader who values precision and the ability to fine-tune your brass preparation. Whether you're tuning for match accuracy or optimizing for a tight-chambered rifle, the bushing full length die gives you the control you need.
| Caliber | 6.5 Grendel |
| Die Type | Bushing Full Length Sizing Die |
| Press Compatibility | Standard 7/8"-14 thread (most single-stage and progressive presses) |
| Material | Heat-treated steel, hardened to L.E. Wilson specification |
| Neck Sizing Method | Interchangeable bushings (sold separately) |
| Neck Unsized Length | 3/16" at bottom of case neck |
| Lock Nut Thickness | .225" (inside to outside edge) |
| Lock Nut Height | .270" |
| Lock Nut Overall Width | 1.250" OD |
| Included Accessories | Adjustable depth decapping rod, spare decapping punch |
| Bushings | Sold separately; L.E. Wilson and Redding bushings compatible |
L.E. Wilson neck bushings are recommended and will fit perfectly. Redding bushings are also compatible with this die. Bushings are sold separately, allowing you to match your brass and desired neck tension.
The L.E. Wilson bushing full length die uses standard 7/8"-14 threads, so it fits virtually all single-stage reloading presses and most progressive presses on the market.
The die comes with an adjustable depth decapping rod and a spare decapping punch, so you can begin sizing brass immediately. You will need to purchase a neck bushing separately to set your desired neck tension—this is not included.
This die sizes the case body, shoulder, and most of the neck while deliberately leaving the bottom 3/16" of the neck unsized. This design approach is preferred by many reloaders for improved accuracy and chamber fit.
L.E. Wilson
The L.E. Wilson 6.5 Grendel bushing full length die is a precision reloading die built for shooters who want control over neck tension without sizing the entire neck. If you're loading for your 6.5 Grendel and looking to improve consistency and accuracy, this die gives you the flexibility to dial in your exact brass dimensions. It sizes the case body and shoulder while leaving the bottom 3/16" of the neck unsized—a technique many serious reloaders prefer for tighter round-to-round consistency and better chamber fit.
L.E. Wilson's bushing-type full length dies are engineered differently than conventional sizing dies. The die works with interchangeable neck bushings (sold separately) so you can match your specific brass and desired neck tension without resizing the entire neck. This modularity means you're not locked into one neck diameter; swap a bushing and adjust your load as your brass changes or your needs evolve. The die includes an adjustable depth decapping rod and a spare decapping punch, so you're ready to start sizing cases right away.
Built from heat-treated steel hardened to L.E. Wilson's specs—tougher than Grade 8 bolts—this die is made to handle thousands of rounds without wear or tolerance creep. It uses stainless lock nuts and other durable components to resist corrosion and maintain a long, accurate service life. The die fits standard 7/8"-14 reloading presses and integrates seamlessly into any established bench setup. Neck bushings are sold separately; L.E. Wilson bushings are recommended, though Redding bushings will also fit.
This is the right choice if you're a meticulous 6.5 Grendel handloader who values precision and the ability to fine-tune your brass preparation. Whether you're tuning for match accuracy or optimizing for a tight-chambered rifle, the bushing full length die gives you the control you need.
| Caliber | 6.5 Grendel |
| Die Type | Bushing Full Length Sizing Die |
| Press Compatibility | Standard 7/8"-14 thread (most single-stage and progressive presses) |
| Material | Heat-treated steel, hardened to L.E. Wilson specification |
| Neck Sizing Method | Interchangeable bushings (sold separately) |
| Neck Unsized Length | 3/16" at bottom of case neck |
| Lock Nut Thickness | .225" (inside to outside edge) |
| Lock Nut Height | .270" |
| Lock Nut Overall Width | 1.250" OD |
| Included Accessories | Adjustable depth decapping rod, spare decapping punch |
| Bushings | Sold separately; L.E. Wilson and Redding bushings compatible |
L.E. Wilson neck bushings are recommended and will fit perfectly. Redding bushings are also compatible with this die. Bushings are sold separately, allowing you to match your brass and desired neck tension.
The L.E. Wilson bushing full length die uses standard 7/8"-14 threads, so it fits virtually all single-stage reloading presses and most progressive presses on the market.
The die comes with an adjustable depth decapping rod and a spare decapping punch, so you can begin sizing brass immediately. You will need to purchase a neck bushing separately to set your desired neck tension—this is not included.
This die sizes the case body, shoulder, and most of the neck while deliberately leaving the bottom 3/16" of the neck unsized. This design approach is preferred by many reloaders for improved accuracy and chamber fit.
