Loading...
Loading...
Loading...
Loading...
Redding Reloading Equipment
The Redding Competition Bushing Neck Die for 6.5mm Creedmoor is purpose-built for serious reloaders who demand consistency and control over every thousandth of an inch. If you're a competition shooter or precision handloader who's already invested in preparing your brass to exacting standards, this die lets you size only the neck without a sizing button—giving you the repeatability that matches your meticulous case prep work.
What makes this die stand out is its engineering: the cartridge case sits completely supported and aligned before sizing even begins, then remains cradled in a tightly chambered sliding sleeve as it moves upward. The resizing bushing self-centers on the case neck as the process starts, eliminating the variables that creep into less rigid designs. The decapping rod stays in precise alignment using internal die geometry as a linear support—think of it working like a firing pin would—so you get clean, consistent primer pocket control shot after shot.
The micrometer adjustment lets you fine-tune exactly how much neck length gets sized, which is critical when you're working up loads at the ragged edge of accuracy. No guesswork, no vague feel—just dial in your dimension and trust it. This is the tool for the handloader who refuses to compromise on consistency.
Keep in mind that bushings and shellholders are sold separately, so you'll need to source those to get up and running. A carbide sizing button kit is also available if your process ever calls for it, though the bushing-only design is the draw here for competitive reloaders.
| Caliber | 6.5mm Creedmoor |
| Die Type | Competition Bushing Neck Die |
| Manufacturer | Redding |
| Bushings | Sold separately |
| Shellholders | Sold separately |
Bushings and shellholders are sold separately for this die. You'll need to source the appropriate bushing for your 6.5mm Creedmoor cases and a compatible shellholder to get started.
This die is designed for use without a sizing button. However, carbide sizing button kits are available separately if you decide your process requires one later.
This die is built for competition shooters and precision handloaders who have already carefully prepared their cartridge cases and want tight control over neck sizing without a button. If you're meticulously managing your brass, this die matches that level of dedication.
The micrometer adjustment on the bushing position lets you set and repeat the exact amount of neck length you want sized. Dial in your dimension once and trust it for consistent, repeatable sizing.
Redding Reloading Equipment
The Redding Competition Bushing Neck Die for 6.5mm Creedmoor is purpose-built for serious reloaders who demand consistency and control over every thousandth of an inch. If you're a competition shooter or precision handloader who's already invested in preparing your brass to exacting standards, this die lets you size only the neck without a sizing button—giving you the repeatability that matches your meticulous case prep work.
What makes this die stand out is its engineering: the cartridge case sits completely supported and aligned before sizing even begins, then remains cradled in a tightly chambered sliding sleeve as it moves upward. The resizing bushing self-centers on the case neck as the process starts, eliminating the variables that creep into less rigid designs. The decapping rod stays in precise alignment using internal die geometry as a linear support—think of it working like a firing pin would—so you get clean, consistent primer pocket control shot after shot.
The micrometer adjustment lets you fine-tune exactly how much neck length gets sized, which is critical when you're working up loads at the ragged edge of accuracy. No guesswork, no vague feel—just dial in your dimension and trust it. This is the tool for the handloader who refuses to compromise on consistency.
Keep in mind that bushings and shellholders are sold separately, so you'll need to source those to get up and running. A carbide sizing button kit is also available if your process ever calls for it, though the bushing-only design is the draw here for competitive reloaders.
| Caliber | 6.5mm Creedmoor |
| Die Type | Competition Bushing Neck Die |
| Manufacturer | Redding |
| Bushings | Sold separately |
| Shellholders | Sold separately |
Bushings and shellholders are sold separately for this die. You'll need to source the appropriate bushing for your 6.5mm Creedmoor cases and a compatible shellholder to get started.
This die is designed for use without a sizing button. However, carbide sizing button kits are available separately if you decide your process requires one later.
This die is built for competition shooters and precision handloaders who have already carefully prepared their cartridge cases and want tight control over neck sizing without a button. If you're meticulously managing your brass, this die matches that level of dedication.
The micrometer adjustment on the bushing position lets you set and repeat the exact amount of neck length you want sized. Dial in your dimension once and trust it for consistent, repeatable sizing.
