Loading...
Loading...
Loading...
Loading...
EGW
The EGW Sight Mount for Trijicon RMR is a straightforward solution for mounting a Trijicon RMR red-dot sight on your Ruger SR9, SR40, or SR45. Instead of adding bulk with a separate mounting system, this mount replaces your rear dovetail sight, creating a clean, low-profile setup that keeps your sightline as close to the bore as possible. If you ever want to run iron sights again, you can pull the EGW mount and reinstall your original rear sight—it's a reversible upgrade, not a permanent modification.
This mount is purpose-built for the Ruger SR-series platform, fitting the factory dovetail cut on SR9, SR40, and SR45 models. The installation is straightforward: remove your rear sight, slip the EGW mount into the dovetail, secure it with the included hardware, and you're ready to attach your RMR. The mount comes with all the fasteners you need, and the design accommodates the small set screw adjustment common on these platforms.
Red-dot optics on carry guns and home-defense pistols have become standard for good reason—faster target acquisition, both-eyes-open shooting, and easier sight alignment in low light. The EGW mount removes one barrier to adoption: the complexity and cost of aftermarket slide cuts. For SR-series shooters wanting to run a proven optic like the Trijicon RMR without expensive gunsmithing, this is a practical, reversible choice.
| Manufacturer | EGW (E. German Werks) |
| Compatibility | Ruger SR9, SR40, SR45 |
| Optic Mounting | Trijicon RMR |
| Mount Type | Dovetail replacement sight mount |
| Fastener Size | 5/64" Allen wrench (included screws) |
| Recommended Torque | 15 in/lbs (mounting screws) |
| Finish | Black |
| Hardware Included | Yes (mounting screws and set screw) |
Yes. The EGW Sight Mount is designed specifically for the dovetail cut on Ruger SR-series pistols in these three calibers.
This mount is designed for the Trijicon RMR. Do not attempt to use other optics on this mount.
No. Installation involves removing your rear sight, placing the EGW mount in the dovetail, and tightening the included fasteners with a 5/64" Allen wrench. The full installation process is outlined in the instructions provided with the mount.
Yes. The mount is reversible. You can remove it at any time and reinstall your factory rear sight.
EGW
The EGW Sight Mount for Trijicon RMR is a straightforward solution for mounting a Trijicon RMR red-dot sight on your Ruger SR9, SR40, or SR45. Instead of adding bulk with a separate mounting system, this mount replaces your rear dovetail sight, creating a clean, low-profile setup that keeps your sightline as close to the bore as possible. If you ever want to run iron sights again, you can pull the EGW mount and reinstall your original rear sight—it's a reversible upgrade, not a permanent modification.
This mount is purpose-built for the Ruger SR-series platform, fitting the factory dovetail cut on SR9, SR40, and SR45 models. The installation is straightforward: remove your rear sight, slip the EGW mount into the dovetail, secure it with the included hardware, and you're ready to attach your RMR. The mount comes with all the fasteners you need, and the design accommodates the small set screw adjustment common on these platforms.
Red-dot optics on carry guns and home-defense pistols have become standard for good reason—faster target acquisition, both-eyes-open shooting, and easier sight alignment in low light. The EGW mount removes one barrier to adoption: the complexity and cost of aftermarket slide cuts. For SR-series shooters wanting to run a proven optic like the Trijicon RMR without expensive gunsmithing, this is a practical, reversible choice.
| Manufacturer | EGW (E. German Werks) |
| Compatibility | Ruger SR9, SR40, SR45 |
| Optic Mounting | Trijicon RMR |
| Mount Type | Dovetail replacement sight mount |
| Fastener Size | 5/64" Allen wrench (included screws) |
| Recommended Torque | 15 in/lbs (mounting screws) |
| Finish | Black |
| Hardware Included | Yes (mounting screws and set screw) |
Yes. The EGW Sight Mount is designed specifically for the dovetail cut on Ruger SR-series pistols in these three calibers.
This mount is designed for the Trijicon RMR. Do not attempt to use other optics on this mount.
No. Installation involves removing your rear sight, placing the EGW mount in the dovetail, and tightening the included fasteners with a 5/64" Allen wrench. The full installation process is outlined in the instructions provided with the mount.
Yes. The mount is reversible. You can remove it at any time and reinstall your factory rear sight.
