Loading...
Loading...
Loading...
Loading...
RCBS
The RCBS 9428 Standard Bullet Puller Collet for .32/8mm ammunition gives you a reliable way to salvage brass and components when you need to pull loaded rounds. Whether you've loaded a batch with the wrong powder charge, seated a bullet too deep, or simply need to reclaim brass from old ammo, this collet-style puller handles .32 and 8mm calibers and threads into virtually any single-stage reloading press with standard 7/8-inch-14 threads. It's a straightforward, no-fuss tool that lets you recover both bullets and cases without unnecessary damage.
Setup and operation are simple. Install the collet in your press, insert your loaded cartridge, tighten the collet around the bullet, then work the press ram to extract it. The redesigned collet grips securely and pulls cleanly—a huge advantage over older puller designs that could mark or deform bullets and cases. For reloaders who work with multiple calibers or who routinely reload small rifle and pistol rounds, keeping a few caliber-specific collets on hand means you're always ready to salvage a mistake or recycle once-fired brass.
RCBS has a long track record in reloading equipment, and this bullet puller reflects that same attention to function. It's not fancy, but it works—and in the reloading room, that's what matters. If you reload .32 or 8mm ammunition and want a press-mounted puller that integrates seamlessly with your setup, this collet is a worthwhile addition to your bench.
| Caliber | .32/8mm |
| Thread Size | 7/8-inch-14 |
| Type | Collet-style bullet puller |
| Manufacturer | RCBS |
The RCBS 9428 uses standard 7/8-inch-14 threads, which fit the vast majority of single-stage reloading presses. If your press accepts standard dies with those threads, this puller will work with it.
This is a .32/8mm collet. If you reload other calibers, you would need the appropriate caliber-specific collet for those rounds.
Yes. The collet-style design grips the bullet and pulls it from the case, allowing you to save both components for reloading.
The puller screws directly into your press die station. You simply need your single-stage press, the collet installed, and the loaded cartridges you want to pull.
RCBS
The RCBS 9428 Standard Bullet Puller Collet for .32/8mm ammunition gives you a reliable way to salvage brass and components when you need to pull loaded rounds. Whether you've loaded a batch with the wrong powder charge, seated a bullet too deep, or simply need to reclaim brass from old ammo, this collet-style puller handles .32 and 8mm calibers and threads into virtually any single-stage reloading press with standard 7/8-inch-14 threads. It's a straightforward, no-fuss tool that lets you recover both bullets and cases without unnecessary damage.
Setup and operation are simple. Install the collet in your press, insert your loaded cartridge, tighten the collet around the bullet, then work the press ram to extract it. The redesigned collet grips securely and pulls cleanly—a huge advantage over older puller designs that could mark or deform bullets and cases. For reloaders who work with multiple calibers or who routinely reload small rifle and pistol rounds, keeping a few caliber-specific collets on hand means you're always ready to salvage a mistake or recycle once-fired brass.
RCBS has a long track record in reloading equipment, and this bullet puller reflects that same attention to function. It's not fancy, but it works—and in the reloading room, that's what matters. If you reload .32 or 8mm ammunition and want a press-mounted puller that integrates seamlessly with your setup, this collet is a worthwhile addition to your bench.
| Caliber | .32/8mm |
| Thread Size | 7/8-inch-14 |
| Type | Collet-style bullet puller |
| Manufacturer | RCBS |
The RCBS 9428 uses standard 7/8-inch-14 threads, which fit the vast majority of single-stage reloading presses. If your press accepts standard dies with those threads, this puller will work with it.
This is a .32/8mm collet. If you reload other calibers, you would need the appropriate caliber-specific collet for those rounds.
Yes. The collet-style design grips the bullet and pulls it from the case, allowing you to save both components for reloading.
The puller screws directly into your press die station. You simply need your single-stage press, the collet installed, and the loaded cartridges you want to pull.
