Loading...
Loading...
Loading...
Loading...
Accu-Shot
When you're running an Atlas 5-H or Super CAL bipod, the feet are where rubber meets dirt—and where your shot stability actually lives. The Accu-Shot Raider Cleat Feet are machined replacement feet designed to swap into those specific Atlas models, giving you aggressive ground bite and durability where it matters most. Built from 416 stainless steel and turned as a single piece, they're engineered to handle field use without degrading or corroding, whether you're prone on hard ground, gravel, or muddy terrain. This is the kind of accessory that lives in the background until you need it, then proves its worth on the shot that counts.
Installation is straightforward: a stainless steel plunger holds the feet in place, so swapping them out takes seconds in the field or at the bench. The cleat design bites into unstable surfaces better than standard feet, reducing creep and micro-movement during your shot sequence—the kind of marginal gain that adds up when you're hunting or shooting long-range. If your Atlas bipod feet are worn, lost, or you want more aggressive ground grip, these are a direct bolt-in solution.
Accu-Shot makes these feet from bar stock in one piece, which means no welds or assembly points to fail under pressure. They're sold as a matched pair, so you get both feet at once. Raw stainless steel finish means they'll age with your gear and resist corrosion in wet conditions or long storage.
| Material | 416 Stainless Steel |
| Cleat Length | Approximately 1.225" |
| Maximum Outer Diameter | Approximately 1.443" |
| Weight (Pair) | 4.76 ounces |
| Quantity | Pair (2 feet) |
| Finish | Raw Stainless Steel |
These Raider Cleat Feet are compatible with Atlas 5-H and Super CAL model bipods only. They will not fit other Atlas models or bipod brands. Check your bipod model before ordering.
Installation uses a press-fit design with a stainless steel plunger. The process is simple enough to do in the field, but we recommend consulting your Atlas bipod manual or contacting us if you need step-by-step guidance.
The cleat foot bites more aggressively into soil, gravel, and uneven ground than standard feet, reducing creep and lateral movement during shooting. This translates to more stable shot sequences, especially on unstable terrain.
Yes, you receive both feet in this purchase—a matched pair ready to install on your bipod.
Accu-Shot
When you're running an Atlas 5-H or Super CAL bipod, the feet are where rubber meets dirt—and where your shot stability actually lives. The Accu-Shot Raider Cleat Feet are machined replacement feet designed to swap into those specific Atlas models, giving you aggressive ground bite and durability where it matters most. Built from 416 stainless steel and turned as a single piece, they're engineered to handle field use without degrading or corroding, whether you're prone on hard ground, gravel, or muddy terrain. This is the kind of accessory that lives in the background until you need it, then proves its worth on the shot that counts.
Installation is straightforward: a stainless steel plunger holds the feet in place, so swapping them out takes seconds in the field or at the bench. The cleat design bites into unstable surfaces better than standard feet, reducing creep and micro-movement during your shot sequence—the kind of marginal gain that adds up when you're hunting or shooting long-range. If your Atlas bipod feet are worn, lost, or you want more aggressive ground grip, these are a direct bolt-in solution.
Accu-Shot makes these feet from bar stock in one piece, which means no welds or assembly points to fail under pressure. They're sold as a matched pair, so you get both feet at once. Raw stainless steel finish means they'll age with your gear and resist corrosion in wet conditions or long storage.
| Material | 416 Stainless Steel |
| Cleat Length | Approximately 1.225" |
| Maximum Outer Diameter | Approximately 1.443" |
| Weight (Pair) | 4.76 ounces |
| Quantity | Pair (2 feet) |
| Finish | Raw Stainless Steel |
These Raider Cleat Feet are compatible with Atlas 5-H and Super CAL model bipods only. They will not fit other Atlas models or bipod brands. Check your bipod model before ordering.
Installation uses a press-fit design with a stainless steel plunger. The process is simple enough to do in the field, but we recommend consulting your Atlas bipod manual or contacting us if you need step-by-step guidance.
The cleat foot bites more aggressively into soil, gravel, and uneven ground than standard feet, reducing creep and lateral movement during shooting. This translates to more stable shot sequences, especially on unstable terrain.
Yes, you receive both feet in this purchase—a matched pair ready to install on your bipod.
